Taconic TLF-35 High Frequency PCB with 30mil, 60mil Thick Coating Immersion Gold, HASL, Immersion Silver and Tin
(PCB's are custom-made products, the picture and parameters shown are just for reference)
Hello everyone,
Today, we talk about TLF-35 high frequency PCB.
Taconic TLF-35 is an organic-ceramic laminates which is based on woven glass reinforcement. It is a result of both ceramic fill technology and coated PTFE fiberglass.
Typical Values of TLF-35
| Property | Test Method | Units | Value | Units | Value |
| Dielectric Constant @ 1.9 GHz | IPC-TM650 2.5.5.5.1 Mod | | 3.50 ±0.05 | | 3.50 ±0.05 |
| Dissipation Factor @ 1.9 GHz | IPC-TM650 2.5.5.5.1 Mod | | 0.0016 | | 0.0016 |
| Dissipation Factor @ 10 GHz | IPC-TM650 2.5.5.5.1 Mod | | 0.0022 | | 0.0022 |
| Water Absorption | IPC-TM 650 2.6.2.1 | % | 0.03 | % | 0.03 |
| Peel Strength (1 oz. copper) | IPC-TM 650 2.4.8 | Lbs./linear inch | 10 | N/mm | 1.8 |
| Volume Resistivity | IPC-TM 650 2.5.17.1 | Mohm·cm | 2.0 x 109 | Mohm·cm | 2.0 x 109 |
| Surface Resistivity | IPC-TM 650 2.5.17.1 | Mohm | 3.0 x 108 | Mohm | 3.0 x 108 |
| Flexural Strength Lengthwise | IPC-TM 650 650 2.4.4 | psi | 13000 | N/mm2 | 90 |
| Flexural Strength Crosswise | IPC-TM 650 650 2.4.4 | psi | 13000 | N/mm2 | 90 |
| Thermal Conductivity | IPC-TM 650 2.4.50 | W/m/K | 0.37 | W/m/K | 0.37 |
| x-y CTE (50 ~ 150℃) | IPC-TM 650 2.4.41 | ppm/℃ | 9-12 | ppm/℃ | 9-12 |
| z CTE (50 ~ 150℃) | IPC-TM 650 2.4.41 | ppm/℃ | 80 | ppm/℃ | 80 |
| Flammability | UL-94 | | V-0 | | V-0
|
We benefit from its following advantages:
1. Improved phase intermodulation distortion (PIMD) with DK3.5
TLF-35 is designed to obtain improved PIMD performances on size effective PCBs for antenna application. The dielectric constant of TLF-35 is 3.5 which is similar with PIMD required levels.
2. Improved PTH quality
It shows better PTH quality which results in more stable hole wall and insulation resistance even for the smaller drilled holes.
3. Stable at high frequency
TLF-35 is designed to offer superior high frequency performance.
4. Low moisture absorption
Its ultra-low moisture absorption rate and low dissipation factor minimize phase shift with frequency.
5. Cost.
Low cost realizes high volume commercial microwave and radio frequency application.
Typical applications are shown as follows.
1. Antenna
2. Power amplifiers (TD-SCDMA, WCDMAS, LTE, WLAN etc.)
3. LNA, Repeater PA
4. Passive RF components (Filters, Couplers etc.)
Our PCB Capability (TLF-35)
| PCB Capability |
| PCB Material: | Organic-ceramic Laminates |
| Designation: | TLF-35 |
| Dielectric constant | 3.50 ±0.05 |
| Layer count: | 1 Layer, 2 Layer, 4 Layer. |
| Copper weight: | 0.5oz, 1oz, 2oz |
| PCB thickness: | 0.8mm, 1.6mm |
| PCB Size: | ≤400mm X 500mm |
| Surface finish: | Bare copper, HASL, ENIG, Immersion tin etc. |
| | |
We’re able to supply TLF-35 high frequency PCB with 1oz and 2oz copper, 0.8mm and 1.6mm thick, maximum panel size 400 X 500mm, with surface finish bare copper, HASL, ENIG, immersion tin etc.
Bicheng specializes in providing you with prototype, small batches and mass production service.
If you have any questions, please feel free to contact us.
Thank you for your reading.
Product Tags:
|
|
TLF-35 400x500mm Multilayer Taconic PCB Board Bare Copper Surface Finish Images
|
